Technologies
Highback
Rear Entry
Often called speed entry, allows you to quickly and easily get in your bindings. Simply open the highback, slide your foot in and then close the highback on your boot.
Highback Forward Lean Adjustment
With this system you have more control over response of your bindings. The more you lean the highback forward, the more response you will get.
Symmetrical Highback
Classic symmetrical highback.
Asymmetrical Highback
With these bindings you will get the most comfort and response when using the ‘ducked’ stance, when your feet are not parallel, but slightly pointing towards the nose and tail of the board.
Highback Rotation Adjustment
Rotate your highbacks to achieve maximum response and comfort.
Buckles
Aluminium Buckles
Buckles made with very durable, ultra-lightweight aluminum.
Composite Buckles
Buckles made with durable, lightweight composite material.
Micro Buckles
Fluent adjustment system allows you to get the perfect fit.
Mount system
4x4 Mount System
Standard mount system where holes are 4 cm apart. Uses a 4 hole disc binding.
3D Mount System
Burton standard that requires a 3 hole disc binding.
The Channel Mount System
The newest Burton standard that utilizes a rail to mount the binding.
Toe strap
Classic Toe Strap
Standard strap that holds the boot from the top.
Cap-Strap
Toe cap wraps around the front of your boot reducing pressure points and giving more response.
Multi Cap-Strap
These straps can be set in both positions: classic ‘over the top’ or modern ‘over the toes’. You can adjust them to your personal preference.
3D Ultralight Tech Cap-Strap
3D shape for the perfect fit with reduced weight for maximum response.
3D Advanced Fit Cap-Strap
3D shape that eliminates pressure points for enhanced comfort.
Ankle strap
3D Ankle Strap
3D shape that eliminates pressure points for enhanced comfort.
Inverted Ankle Strap
Comes with the seam on the outside providing more comfort.
Ultralight Ankle Strap
Reduced weight for maximum response.
Mountain Ankle Strap
Wide strap with extra support, optimized for big mountain riding.
Double Flex Technology
Flip the strap upside down to switch the upper and lower stiffness levels and optimize it to your personal needs.
Base
Aluminium Base
Base made with very durable, ultra-lightweight aluminum.
Composite Base
Base made with durable, lightweight composite material.
Foot bed
Foot Bed Rubber Pads
Rubber pads provide grip and cushioning.
Fully Padded Foot Bed
Foot bed fully padded for maximum cushioning and comfort.
Gas pedal
Adjustable Front Gas Pedal
Adjusting gas pedals lets you accommodate larger boots, reducing toe drag and giving more power and response.
Adjustable Rear Gas Pedal
Adjusting gas pedals lets you accommodate larger boots, reducing toe drag and giving more power and response.
Heel cup
Adjustable Heel Cup
Heel cup that provides an easy way to center your boots over the board.
Flex
Binding Flex
The flex of your bindings should correspond with the flex of your boots and snowboard. Choose one based on your riding style!
Core
Poplar Wood Core
Super strong, super light, low moisture ratio core. You may believe us or not but we really do control precisely every single tree before it’s changed into vertically laminated wood strips. This ensures each board has exactly the same amount of pop and flex. The German glue used for gluing the wood strips is made of only the best natural components and this is the reason why our boards never delaminate and it makes our boards eco-friendly.
Sidewall
ABS Sidewall
Sidewall structure is responsible for the power transmission to the edges. It also supports and reinforces the top edge and absorbs shocks. In order to better protect the core against external damages and penetrating the moisture into the core, our sidewalls are made only from the best quality high molecular bonding ABS produced in Austria. Our long time experience shows that 30 degrees sidewalls improve power transfer over the edge and offer better vibration damping.
Lamination
High Density Fiberglass
Our lightweight high density premium biaxial laminates not only possess all the advantages of our standard biaxial laminates but also provide additional stability, offer over 10% more pop and over 5% more torsional and longitudinal stiffness comparing to the standard laminates.
Triax Fiberglass
Light-weight, multi axis, stitched fiberglass laminate that provides excellent torsional and longitudinal rigidity, great pop and response for a precise controlled ride.
Profile
Classic Camber
Our classic camber snowboards have 15 mm of camber underneath. It offers a very good edge control. The camber shape provides precision turning on finely groomed runs of hard-packed snow but also offers increased hold in the half pipe as it can bend with the curvature of the ramp walls. The unique shape of the camber snowboard has the ability to absorb the landing impact of high-altitude tricks.
Camrocker Profile
Micro camber between the bindings, with rocker in the tip and tail from the bindings out. One of the key advantages this board profile is its advanced performance on slopes that are covered with freshly fallen snow. The unique shape of our 3-Stage Rocker design permits the snowboard to rock back and forth during jibbing tricks but it’s also great for beginners as it helps prevent you from catching an edge.
Flatrocker Profile
Flat section between the bindings, with rocker in the tip and tail from the bindings out. The flat part of the board offers better edge grip than rocker and better maneuverability than camber. The rocker sections bring the tip and tail up and off the snow, shortening the contact length of the edges and making turns easier. Your ride becomes more nimble and maneuverable. You can slash the snow, slide sideways to scrub speed, smear and butter turns.
Flat Profile
Flat, also called zero camber, combines the benefits of both – rocker and camber. It makes easy transitions, with better edge grip than rocker and better maneuverability than camber. It’s a versatile option, super stable for riding rails, due to the flat surface between the bindings. It requires less ollie force to get it in the air compared to a traditional board.
Full Rocker (Reverse Camber) Profile
There are many benefits of riding a full rocker. The contact points raise above the snow and make the board less likely to catch an edge. The board feels more forgiving and pivots easily. Turn initiations are smoother and powder floatation is enhanced. Full rockers are also great for freestyling and super stable for riding rails. They boost the playful feel and make pressing and jibbing easy.
Hybrid Rocker Profile
It’s a good choice for those riders who like the best of both worlds. Reverse camber between the feet keep it loose, playful and floaty, while positive camber in the nose and tail deliver a ton of pop and stability and edge hold. Camrocam offers great float in powder and a catch-free freestyle performance. It feels more like a rockered board than a cambered board when you ride it.
Hybrid Camber Profile
It offers great ollie-pop, is more forgiving than the classic camber profile and allows quick and grippy edge-to-edge turns.
Shape
Directional Shape
The binding inserts are set back, the flex is uneven, the sidecut is progressive, the tip and tail are different width and length.
Directional Twin
The binding inserts are set back, the flex is even, the sidecut is radial, the tip and tail are exactly the same width but the nose is longer than the tail.
Twin Shape
The binding inserts are set back, the flex is even, the sidecut is radial, the tip and tail are exactly the same width and length.
True Twin Shape
A true twin shape means the board is 100% symmetrical – the stance is centered, the flex is even, the sidecut is dual-progressive, the tip and tail are exactly the same width and length.
Base
Extruded Base
Extruded bases are easy and cheap to maintain. They do not need to be waxed much. We only use the best quality Austrian bases made by the leading company – Isosport.
Reinforcement
Carbon Stringers
Carbon stringers are added to selected models to improve pop, torsional stiffness and to add response to your edges and your ollies.
UEH
Ultra Edge Hold
Our technology combines two intersecting sidecuts with additional contact points. The additional contact points arcs are located just outside the binding mounting area. They add quickness and control at slow speeds, and edge control at high speeds.
Flexibility
Board Flex
Our board flexes are based on a scale of soft – stiff.
en
pl
en